Search found 8 matches

Return to advanced search

Re: Adept ACE "Checking for ACE server on controller"

Hello Arceles, do you have a dongle with a license for running the UI in a non emualtion environment? If so please check if your dongle is detected by the pc. If you don't have the dongle with the license you are not able to run the UI in a production environment. Please note that Youtube is the wro...
by PeterL
Wed Feb 08, 2017 6:42 am
 
Forum: Adept ACE
Topic: Adept ACE "Checking for ACE server on controller"
Replies: 1
Views: 4039

Re: "specified path invalid" error in ACE when adding camera

Hi Matt,

Basler USB3.0 cameras are supported from ACE 3.5.

-Peter
by PeterL
Mon Dec 08, 2014 12:28 pm
 
Forum: Adept ACE
Topic: "specified path invalid" error in ACE when adding camera
Replies: 1
Views: 6150

Re: Adept Robot Utility disk & V+ Operating System Files NE

Hallo Josef, entschuldige die späte Antwort. Was zeigen die Led's des 030 Processor boards und der SIO an? Haben diese beiden Karten schon einmal zusammen in einem Controller funktioniert? Bei ganz alten 030 Boards gibt es ein Problem mit einem Timeout während der Initialisierung der Festplatte. Wel...
by PeterL
Sun May 02, 2010 11:32 am
 
Forum: German
Topic: Adept Robot Utility disk & V+ Operating System Files NE
Replies: 1
Views: 10167

Re: Tracking without vision and Smartcontroller Cx

The reference for your belt tracking is a belt calibration you do with belt_cal.v2 from the utils. In this calibration file the sacle factor from the belt encoder, belt.nom and the belt window are specified.This calibration will create a belt.dat file that you have to load using loadbelt.v2 from the...
by PeterL
Thu Mar 04, 2010 9:34 am
 
Forum: V+
Topic: Tracking without vision and Smartcontroller Cx
Replies: 2
Views: 7074

Re: DeviceNet as Master

Here you will find information about the DeviceNet configuration of a SmartController unit: http://www1.adept.com/main/ke/DATA/v%20 ... ig_c2.html
As long as the MACID in the LOCAL statement is set to "0" the SmartController is the master.
by PeterL
Sat Feb 06, 2010 4:53 am
 
Forum: SmartController CX Robot Control
Topic: DeviceNet as Master
Replies: 3
Views: 17076

Re: FCOPY

The FCOPY syntax is FCOPY destination = source .

If you give us more information about your installation (controller type, software) we can give you further information about destination and source for your case.
by PeterL
Mon Aug 10, 2009 1:28 pm
 
Forum: V+
Topic: FCOPY
Replies: 1
Views: 4843

Re: Data across a Profibus DP/Devicenet bridge

Yes we use the DN-CBM-DP Profibus-DP / DeviceNet Gateway from esd-electronics for this. You must configure the Gateway from the Siemens-PLC site and set a MACID that is between 1...63, the baudrate and the number of inputs and outputs. The Adept controller must be configured as MACID 0 and the baudr...
by PeterL
Wed Apr 08, 2009 2:55 am
 
Forum: SmartController CX Robot Control
Topic: Data across a Profibus DP/Devicenet bridge
Replies: 2
Views: 15829

Re: trouble with Viper S650.

Hello, it sounds you have a hardware problem on your system. The mounting of the robot can cause this vibration but I don't think this is really the problem you have. D3 (Duty cycle exceeded Mtr.3) means that to much current was applied to this motor over a long time. So it seems something is blocki...
by PeterL
Fri Jan 02, 2009 3:23 pm
 
Forum: Viper s650/s850
Topic: trouble with Viper S650.
Replies: 1
Views: 16261

Return to advanced search

cron